Replace your hood's prop rod today with this Redline Tuning Hood QuickLIFT system. Progressive gas springs will lift and hold your hood without the need for a poorly placed prop-rod, simply start to lift your hood and let the QuickLIFT system take over. Our Jeep JL & JT Hood QuickLIFT system is simply the best on the market. This design is entirely bolt-in and will take only a five minutes to install using only a 10mm socket. You'll use existing mounting locations on the vehicle for the QuickLIFT system's lifting action.
These Systems include Quick-release end-fittings on the gas struts for the Jeep models. This allows the user to easily remove the strut from the lower attachment and then place the hood all the way back onto the wind-shield.
FITMENT: This Jeep Wrangler & Gladiator Hood QuickLIFT PLUS system is designed to fit US OEM Jeep Wrangler & Gladiator (JK, JT) models: 2018 2019 2020 2021 2022+.
NOTE: If you have the Mojave Edition or a vehicle OUTSIDE North America, purchase 21-20006-02 system.
If you have a Rubicon 392, purchase 21-20007-02. These vehicles have heavier OEM hoods and require higher force gas springs. All of the mounting hardware is the same for the 2018+ Jeep models, but the gas struts are different based on the hood application.
Prop rod can be removed once installed
Patent Pending Attachment System
Progressive, slow release gas springs - final few inches of operation, gas springs slow down extending rate allowing for a fluid lifting process.
Silver zinc-plated hardware in base QuickLIFT system
Black powder coated hardware in QuickLIFT PLUS and ELITE
316L Stainless steel gas springs in QuickLIFT ELITE
Full color installation manual with every QuickLIFT system
CAD designed hardware unique to each QuickLIFT application
These Systems include Quick-release end-fittings on the gas struts for the Jeep models. This allows the user to easily remove the strut from the lower attachment and then place the hood all the way back onto the wind-shield.
- NO MODIFICATIONS TO JEEP
- 5 MINUTE INSTALLATION - Very simple & quick installation
- USES EXISTING MOUNTING LOCATIONS
- TOOLS - 10mm socket and wrench, that's it!
- QUICK-RELEASE - Rod ends have quick-release feature so that you can remove and lay the hood all the back against the windshield.
- LIFTS & HOLDS HOOD without prop rod - just start to lift and let our Hood QuickLIFT System lift and hold up your hood.
FITMENT: This Jeep Wrangler & Gladiator Hood QuickLIFT PLUS system is designed to fit US OEM Jeep Wrangler & Gladiator (JK, JT) models: 2018 2019 2020 2021 2022+.
NOTE: If you have the Mojave Edition or a vehicle OUTSIDE North America, purchase 21-20006-02 system.
If you have a Rubicon 392, purchase 21-20007-02. These vehicles have heavier OEM hoods and require higher force gas springs. All of the mounting hardware is the same for the 2018+ Jeep models, but the gas struts are different based on the hood application.
 |  |  | ||||
| Slip blind-insert into slot & align the bracket vertically until you can install lower bracket bolt. | Tuck NVH felt liner on top of bracket, then tighten down bolts | Bracket uses existing 10mm bolt, rests on the fender lip for secure support of gas strut. |
Prop rod can be removed once installed
Patent Pending Attachment System
Progressive, slow release gas springs - final few inches of operation, gas springs slow down extending rate allowing for a fluid lifting process.
Silver zinc-plated hardware in base QuickLIFT system
Black powder coated hardware in QuickLIFT PLUS and ELITE
316L Stainless steel gas springs in QuickLIFT ELITE
Full color installation manual with every QuickLIFT system
CAD designed hardware unique to each QuickLIFT application
